GENERAL
INFORMATION
The Multipoint Fuel Injection System consists of sensors which detect the engine conditions,
the engine-A/T-ECU which controls the system based on signals from these sensors, and actuators
which operate under the control of the engine-A/T-ECU. The engine-A/T-ECU carries out activities
such as fuel injection control, idle speed control and ignition timing control. In addition,
the engine-A/T-ECU is equipped with several diagnosis modes which simplify troubleshooting when
a problem develops.FUEL INJECTION CONTROL
The injector drive times and injector timing are controlled so that the optimum air/fuel
mixture is supplied to the engine to correspond to the continually-changing engine operation
conditions. A single injector is mounted at the intake port of each cylinder. Fuel is sent under pressure from the fuel tank by the fuel pump, with the pressure being regulated by the fuel pressure regulator. The fuel thus regulated is distributed to each of the injectors.
Fuel injection is normally carried out once for each cylinder for every two rotations of the crankshaft. The firing order is 1-3-4-2. This is called sequential fuel injection. The engine-A/T-ECU provides a richer air/fuel mixture by carrying out "open-loop" control when the engine is cold or operating under high load conditions in order to maintain engine performance. In addition, when the engine is warm or operating under normal conditions, the engine-A/T-ECU controls the air/fuel mixture by using the oxygen sensor signal to carry out "closed-loop" control in order to obtain the theoretical air/fuel mixture ratio that provides the maximum cleaning performance from the three way catalyst.
IDLE AIR CONTROL
The idle speed is kept at the optimum speed by controlling the amount of air that bypasses
the throttle valve in accordance with changes in idling conditions and engine load during idling.
The engine-A/T-ECU drives the idle speed control motor to keep the engine running at the pre-set
idle target speed in accordance with the engine coolant temperature and air conditioner load.
In addition, when the air conditioner switch is turned off and on while the engine is idling,
the idle speed control motor operates to adjust the throttle valve bypass air amount in accordance
with the engine load conditions in order to avoid fluctuations in the engine speed.IGNITION TIMING CONTROL
The power transistor located in the ignition primary circuit turns ON and OFF to control
the primary current flow to the ignition coil. This controls the ignition timing in order to
provide the optimum ignition timing with respect to the engine operating conditions. The ignition
timing is determined by the engine-A/T-ECU from the engine speed, intake air volume, engine
coolant temperature and atmospheric pressure.SELF-DIAGNOSIS FUNCTION
- When an abnormality is detected in one of the sensors or actuators related to emission control, the engine warning lamp (check engine lamp) illuminates as a warning to the driver.
- When an abnormality is detected in one of the sensors or actuators, a diagnosis code corresponding to the abnormality is output.
- The RAM data inside the engine-A/T-ECU that is related to the sensors and actuators can be read by means of the MUT-II/III. In addition, the actuators can be force-driven under certain circumstances.
OTHER CONTROL FUNCTIONS
- Fuel Pump Control
Turns the fuel pump relay ON so that current is supplied to the fuel pump while the engine is cranking or running.
- A/C Relay Control
Turns the compressor clutch of the A/C ON and OFF.
- Fan Motor Control
The revolutions of the radiator fan and condenser fan are controlled in response to the engine coolant temperature and vehicle speed.
- Purge Control Solenoid Valve Control
(Refer to GROUP 17 - Engine And Emission Control - Evaporative Emission Control System
).
- EGR Control Solenoid Valve Control
[Refer to GROUP 17 - Engine And Emission Control - Exhaust Gas Recirculation (EGR) System].
GENERAL SPECIFICATIONS
| Items |
Specifications |
|
|---|---|---|
| Throttle body |
Throttle bore mm |
54 <SOHC> 60 <DOHC> |
| Throttle position sensor |
Variable resistor type |
|
| Idle speed control servo |
Stepper motor type |
|
| Engine-A/T-ECU |
Identification No. |
E6T36478 <SOHC> E6T41473 <DOHC> |
| Sensors |
Air flow sensor |
Karman vortex type |
| Vacuum pressure Sensor (Manifold absolute pressure sensor) <SOHC> |
Semiconductor type |
|
| Vacuum pressure Sensor (Manifold differential pressure sensor) <DOHC> |
Semiconductor type |
|
| Intake air temperature sensor |
Thermistor type |
|
| Engine coolant temperature |
Thermistor type |
|
| Oxygen sensor |
Zirconia type |
|
| Inhibitor switch |
Contact switch type |
|
| Camshaft position sensor |
Hall element type |
|
| Crank angle sensor |
Hall element type |
|
| Detonation sensor |
Piezoelectric type |
|
| Power steering fluid pressure switch |
Contact switch type |
|
| Actuators |
Engine control relay type |
Contact switch type |
| Fuel pump relay type |
Contact switch type |
|
| Injector type and number |
Electromagnetic type, 4 |
|
| Injector identification mark |
CDH 240 |
|
| EGR control solenoid valve |
Duty cycle type solenoid valve |
|
| Purge control solenoid valve |
Duty cycle type solenoid valve |
|
| Fuel pressure regulator |
Regulator pressure kPa |
329 |
)
)