REMOVAL AND INSTALLATION <L.H. DRIVE VEHICLES>

For removal and installation of the passenger's side air bag module, always observe the service procedures described in GROUP 52B, Air Bag Module and Clock Spring

The following bolts and screws are used for installing the instrument panel. Bolts and screws are indicated as marks shown in the illustration in the sections of "Removal and Installation" and "Disassembly and Assembly."

Name	Symbol	Size (D × L) mm	Colour
Tapping screw	a	5 × 12	-
	b	5 × 16	-
	c	5 × 16	Black
	d	4 × 10	-
	e	5 × 12	-
	f	5 × 20	-
Washer assembly bolt	g	6 × 16	-
	h	6 × 16	-
	i	6 × 16 (Earth)	-
	j	10 × 60	-

CAUTION

Refer to GROUP 52B, SRS Service Precautions and Air bag Module and Clock Spring before removing the passenger side air bag module.

Do not subject the SRS-ECU to any shocks when removing or installing the instrument panel.

Pre-removal and Post-installation Operation

Removal and Installation of Front Floor Console (Refer to ).

Removal and Installation of Steering Wheel (Refer to GROUP 37, Steering Wheel ) and Air Bag Module Assembly (Refer to GROUP 52B, Air bag module and clock spring ).

			Removal steps
		1.	Instrument panel clock garnish
<<A>>		2.	Instrument panel air outlet (centre)
		3.	Clock
		4.	Instrument panel driver’s side garnish
		5.	Meter bezel
		6.	Combination meter
		7.	Junction block cover <Vehicles for Argentina>
		•	Hood lock release handle (Refer to GROUP 42, Hood ).
		8.	Instrument panel parcel box
		•	Floor harness (R.H.) and junction block connection
		9.	Instrument lower panel
<<A>>		10.	Instrument panel air outlet (L.H.)
		11.	Instrument panel lower panel bracket
		12.	Column cover
		•	Air mix door cable, blow vent changeover damper cable connection (Refer to GROUP 55A, Heater Control Assembly and A/C Switch ).
		13.	Knob
	>>A<<	14.	Centre panel
		15.	Box
		16.	Manual air conditioner control panel
		17.	Radio plug <Vehicles for Argentina and Brazil>
		18.	Radio with tape player and CD changer assembly <Vehicles for GCC and General export (except for Argentina)> <Option for CD changer>
		19.	Centre lower panel
		20.	Centre lower box
		21.	Centre lower cover
		•	Front scuff plate, cowl side trim (Refer to ).
		22.	Back bone spacer
		23.	Glove box stopper
		24.	Glove box
		25.	Connector block
		26.	Instrument panel side cover
		•	Roof harness connection
		•	Instrument panel harness earth connection
		•	Instrument panel and body harness connection
		•	Steering shaft harness connector and clamp
		•	Stop lamp switch connector
		•	SRS-ECU connector
		•	Shift lock cable clamp
		•	Steering shaft installation bolt (Refer to GROUP 37, Steering Shaft ).
		27.	Instrument panel assembly

CLIP AND CLAW POSITIONS

REMOVAL SERVICE POINT

<<A>> INSTRUMENT PANEL AIR OUTLET REMOVAL

The instrument panel air outlet may remain on the instrument panel side when disassembling the lower panel of the instrument panel and the instrument panel garnish. Carefully disassemble the parts remaining on the instrument panel side to prevent the ball and spring from falling. Assemble the ball and spring according to the figure to the left if they fall off.

INSTALLATION SERVICE POINT

>>A<< CENTRE PANEL ASSEMBLY INSTALLATION

Air mix door cable and blow vent changeover damper cable connection (Refer to GROUP 55A, Heater Control Assembly and A/C Switch