Pre-removal and Post-installation Operation
|
)
| Front door sash tape removal step |
|||
|---|---|---|---|
<<A>> |
>>A<< |
1. |
Door sash tape rear |
| Rear door sash tape removal step |
|||
| <<A>> |
>>B<< |
2. |
Door sash tape front |
| <<A>> |
>>B<< |
3. |
Door sash tape rear |
REMOVAL SERVICE POINT
INSTALLATION SERVICE POINT
>>A<<
FRONT DOOR SASH TAPE REAR INSTALLATION
- The ambient temperature should be 20
to
30°C . Ensure that the working area is clean. Ideally, the tape application should be done at ambient temperature of25°C . - If ambient temperature is less than
15°C , heat the tape and application surface to a temperature of 20 to30°C . If ambient temperature is35°C or higher, cool down them. - The adhesive property of the tape is deteriorated at low temperature, so the tape may come adrift easily. Meanwhile, it gets softened at hot temperature.
- When beginning to apply the tape, pay particular attention. If the end of the tape cannot be applied to the specified position with an accuracy of less than 1 mm, it may cause the poor appearance or adhesion.
CAUTION)
- Use the special tool Stripe Tape Spatula (MB990528) to apply the tape with a steady pace and pressure. If you do not apply the tape with a steady pace or pressure, or abort the application, a shallow groove (lateral groove called as "Shock line") may be present on the tape surface. Meanwhile, if you apply it too quickly, air bubbles may be formed under the tape.
- Wrap a soft cloth (synthetic fiber) around the tip of the special tool.
- Use isopropyl alcohol to degrease the tape application surface.
- Wipe away dirt from the tape.
- Apply the front door sash tape rear according to the procedure below.
)
- Align the tape with the upper and lower specified position.
- Peel off the backing paper of the upper side by the cut line, and apply the top of tape temporarily.
)
- Peel off the backing paper under the tape by half of all tape.
- Press the tape by a special tool Stripe Tape Spatula (MB990528).
- While peeling off the remaining backing paper from up to down, press the tape by a special tool (MB990528).
- Peel off the application tape from up to down towards 180 degrees.
)
- Press the folded area of the tape end at 3 steps (60 degrees, 120 degrees, and holding), while rolling it toward the vehicle inside.
)
- Finally, press the A area strongly by finger and roll the tape inside thoroughly (there are three slits on the tape).
>>B<<
REAR DOOR SASH TAPE FRONT/REAR INSTALLATION
- The ambient temperature should be 20
to
30°C . Ensure that the working area is clean. Ideally, the tape application should be done at ambient temperature of25°C . - If ambient temperature is less than
15°C , heat the tape and application surface to a temperature of 20 to30°C . If ambient temperature is35°C or higher, cool down them. - The adhesive property of the tape is deteriorated at low temperature, so the tape may come adrift easily. Meanwhile, it gets softened at hot temperature.
- When beginning to apply the tape, pay particular attention. If the end of the tape cannot be applied to the specified position with an accuracy of less than 1 mm, it may cause the poor appearance or adhesion.
CAUTION
- Use the special tool Stripe Tape Spatula (MB990528) to apply the tape with a steady pace and pressure. If you do not apply the tape with a steady pace or pressure, or abort the application, a shallow groove (lateral groove called as "Shock line") may be present on the tape surface. Meanwhile, if you apply it too quickly, air bubbles may be formed under the tape.
- Wrap a soft cloth (synthetic fiber) around the tip of the special tool.
- Use isopropyl alcohol to degrease the tape application surface.
- Wipe away dirt from the tape.
- Apply the rear door sash tape front/rear according to the procedure below.
)
- Align the tape with the upper and lower specified position.
- Peel off the backing paper of the upper side by the cut line, and apply the top of tape temporarily.
- Peel off the backing paper under the tape by half of all tape.
- Press the tape by a special tool Stripe Tape Spatula (MB990528).
- While peeling off the remaining backing paper from up to down, press the tape by a special tool (MB990528).
- Peel off the application tape from up to down towards 180 degrees.
- Press the folded area of the tape end at 3 steps (60 degrees, 120 degrees, and holding), while rolling it toward the vehicle inside.
)
- Finally, press the A to C areas strongly by finger and roll the tape inside thoroughly.
NOTE:
- In the A area, there are three slits on the tape.
- In the B area, press the stepped section downwards thoroughly.
- In the C area, press the R section thoroughly.