COMMUNICATION METHOD
The exclusive signal lines for transmitting the multi-distribution data are connected
as follows between the ETACS-ECU, column switch (incorporated inside the column-ECU), front-ECU,
sunroof motor assembly (incorporated inside the sunroof-ECU), power window main switch (incorporated
inside the power window-ECU), and power window sub switches (incorporated inside the power window-ECU) <Vehicles
for Argentina>
for internal communication.)
)
When the driver's door is opened with the ignition key inserted in the ignition
key cylinder (with the ignition switch OFF), the buzzer sounds intermittently (ping sound) to
alert the driver that the key is not removed.
)
When the ignition key is removed and then the driver's door is opened with turning
ON the tail lamp or the headlamp, the buzzer sounds continuously to alert the driver that the
lamp is still ON.
However, if the tail lamp or the headlamp is turned off by the headlamp automatic shutdown function <Except vehicles for Australia>, the buzzer does not sound.
However, if the tail lamp or the headlamp is turned off by the headlamp automatic shutdown function <Except vehicles for Australia>, the buzzer does not sound.
)
When the driver's door is locked (when the lock switch turns ON after turning
OFF the unlock switch in the driver's door lock actuator), ETACS-ECU turns ON the lock
relay output for 0.25 second, and locks all doors (including the tailgate).
When the driver's door is unlocked (when the unlock switch turns ON after turning OFF the lock switch on the driver's door lock actuator), ETACS-ECU turns ON the unlock relay output for 0.25 second, and unlocks all doors (including the tailgate).
When the driver's door is unlocked (when the unlock switch turns ON after turning OFF the lock switch on the driver's door lock actuator), ETACS-ECU turns ON the unlock relay output for 0.25 second, and unlocks all doors (including the tailgate).
Key reminder function <Vehicles with keyless entry system>
)
If the discouraging the door lock operation fails, the current supply will be retried. (The unlock relay output is turned ON for 0.25 second up to five times with one second interval.)
NOTE: The broken line in the graph indicates the current supply retry state if the discouraging
door lock operation fails.
DOOR UNLOCK FUNCTION WITH THE IMPACT DETECTION
If the vehicle crashed with the ignition switch ON or 30 seconds after turning the ignition
switch to LOCK (OFF), and the impact sensor detects an impact greater than the specified value,
the impact sensor sends the signal to ETACS-ECU. Then, within the 0.1 second, ETACS-ECU energizes
the unlock relay for one second for releasing the door lock to prevent passengers to kept inside
the vehicle after the crash.NOTE: The fail safe disables the operation under the following conditions. (Diagnosis code No.31
or 32 is output at this time.) Turn ON the ignition switch again after turning the ignition switch
to LOCK (OFF) to return from the fail safe state.
- No.31: When the ignition switch is ON, and the sensor shows under the short circuit detect voltage for 2.5 second
- No.32: When the ignition switch is ON, and the sensor shows over the closed circuit detect voltage for 0.4 second
POWER WINDOW TIMER FUNCTION <EXCEPT VEHICLES FOR AUSTRALIA>
)
If the driver's door is opened during the timer operation, the power window relay is kept ON for 30 seconds from that time. However, when the driver's door is closed, the power window relay is turned OFF at the same time.
POWER WINDOW TIMER FUNCTION <VEHICLES FOR AUSTRALIA>
)
If the driver's or the front passenger door is opened during timer operation, the power window relay is turned OFF at the same time.
Sunroof timer function <Except vehicles for Argentina>
)
)
If the driver's door is closed during sunroof timer operation, the sunroof operation is canceled at the same time. <Except vehicles for Australia>
)
)
The hazard answer back function that allows checking the lock/unlock state of
the door easily even in the daytime is installed. When the lock signal from the keyless entry
transmitter is received into ETACS-ECU, all doors (including the tailgate) are closed, and the
turn-signal lamp blinks twice. When the unlock signal is received, all doors (including the
tailgate) are closed, and the turn-signal lamp blinks once.
NOTE: The answer back blink time can be adjusted by the adjustment function.
)
The room lamp blinks two times while locking the door for easy checking the keyless entry
function. When the door is unlocked, the lamp lamps on for 15 seconds (100%), and turns off.
Intermittent control <Except vehicles for GCC>
(the
initial condition: with function)
)
NOTE: The vehicle speed sensing function can be invalidated by the adjustment function. <Vehicles with
keyless entry system>
)
When the intermittent time TI is elapsed after being turned ON the windshield wiper drive signal, the windshield wiper drive signal is turned ON again, and the above-mentioned operation is repeated.
INTERMITTENT CONTROL <VEHICLES FOR GCC>
)
The front ECU determines the intermittent time TI from the input SWS data, and turns ON the windshield wiper drive signal. When the wiper comes to the stop position, the windshield wiper auto-stop signal is turned OFF, and the windshield wiper drive signal turns OFF.
When the intermittent time TI is elapsed after being turned ON the windshield wiper drive signal, the windshield wiper drive signal is turned ON again, and the above-mentioned operation is repeated.
Mist wiper control
)
Low speed wiper and high speed wiper control
)
When the windshield high speed wiper switch is turned ON, the windshield wiper drive signal turns ON. Also, the wiper speed switch relay turns ON (HI), and the windshield wiper operates at the high speed.
Rear wiper control
)
- When the rear wiper switch on the column switch is
turned ON with the ignition switch at the ACC or ON position, ETACS-ECU turns ON the rear wiper
drive signal for 3 seconds (approximately 2 operations) and performs the intermittent action at
8-second intervals.
When the selector lever is moved to R (reverse) position during the rear wiper operation, the inhibitor switch R (reverse) turns ON one second after that, ETACS-ECU sends the rear wiper drive signal for 3 seconds (approximately 2 operations), and operates the intermittent action in 8 seconds interval.
- By the special operation of the rear wiper switch on the column switch (successive 2-time operations), the rear wiper operates continuously regardless of the set intermittent time.
Headlamp washer control
)
Headlamp automatic shutdown function <Except vehicles for
Australia>
(the initial condition: with function)
)
- If the ignition switch is turned OFF with the lighting switch ON, the lamp turns off automatically after 3 minutes. If the driver's door is opened during the 3 minutes, the lamp turns off after one second. (One seconds before turning off, the lamp remainder buzzer sounds. However, if the driver's door is opened with the ignition key inserted, the key remainder alarm buzzer operates in the first priority.)
NOTE: For vehicles with the keyless entry system, this function can be invalidated by the adjustment function.
)
When the turn-signal lamp switch is ON (LH or RH) with the ignition switch is ON, the
turn-signal lamp output (flash signal) is turned ON.
If the lamp bulb of the front or rear turn-signal lamp has burned out, the flashing speed becomes faster to alert the driver that the lamp bulb has burned out.
If the lamp bulb of the front or rear turn-signal lamp has burned out, the flashing speed becomes faster to alert the driver that the lamp bulb has burned out.
)
When the hazard lamp switch input signal turning from OFF to ON is detected, the flashing
states turns over by the signal. (When the hazard lamp is not blinking, it blinks. If it is
blinking, it turns off.)
NOTE:
- The push-return switch is adopted for the hazard lamp switch.
- Even if the lamp bulb has burned out, the flashing speed of the hazard lamp is not changed.
Front fog lamp control function <Vehicles with front fog lamp>
)
If the tale lamp or the headlamp is turned off with the lighting switch OFF while the fog lamps lit, the fog lamps turn off the same time to prevent unattended operation.
If the tail lamp is turned off by the headlamp automatic shutdown function, the fog lamps turn off at the same time. However, if the tail lamps light again, the fog lamps do not.
Rear fog lamp control function <Vehicles with rear fog lamp>
)
If the headlamp and the front fog lamp, the rear fog lamp is turned OFF at the same time.
DIMMER INTERIOR LAMP CONTROL FUNCTION (THE INITIAL CONDITION: 15 SECONDS)
)
- When the ignition switch is OFF:
By opening any door or tailgate lamps, the lamp turns ON (100%), and dims (65%) when the door or tailgate is closed, then and turns off after 15 seconds.
However, when the ignition switch is turned ON or the door lock is operated curing the timer operation, the lamps turn off at that time.
- When the ignition switch is ON:
By opening any door or tailgate lamps, the lamp (100%) turns ON and OFF when the door or tail gate is closed.
- When all doors and the tailgate are closed, and the ignition key is removed <Vehicles
with keyless entry system>
By removing the ignition key with all doors and the tailgate closed, the lamp turns ON 100% <Vehicles for GCC and Australia> or 65% <Except vehicles for GCC and Australia>, and turns off after 15 seconds.
By inserting the ignition key again or operating the door lock with the lamp lit, the lamps turns off.
NOTE: For the vehicles with the keyless entry system, the delayed lamp-off time and the operation times
of the keyless entry interior lamp answer back can be changed by the adjusting function.
Interior lamp automatic shutoff function <Vehicles with keyless
entry system>
(the initial condition: with function)
)
- After 30 minutes with the interior lamp lit while the ignition switch is OFF, the lamp turns off automatically.
- After 30 minutes with any door switches opened while the ignition switch is OFF, the lamp turns off automatically.
- Open and close doors.
- Operate the keyless entry transmitter.
- Turn the ignition switch to ACC or ON.
NOTE:
- The interior automatic shutoff function can be disabled or enabled by the adjusting function.
- After returning, the lamp turns off after 30 minutes, when the interior lamp automatic shutoff function is met.
Ignition key cylinder illumination lamp control function
)
)
When the ignition switch is turned to ON, the seat belt warning lamp flashes 4 times (over
6 seconds).