INSPECTION PROCEDURE C-2: A door or a tailgate can not be locked or unlocked by the central door locking system. <RH drive vehicles>

[54D] SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR <Except for Hong Kong spec.> - - SYMPTOM PROCEDURES - CENTRAL DOOR LOCKING SYSTEM - INSPECTION PROCEDURE C-2: A door or a tailgate can not be locked or unlocked by the central door locking system. <RH drive vehicles>

PRINT PAGE / INDEX / PRIOR / NEXT



INSPECTION PROCEDURE C-2: A door or a tailgate can not be locked or unlocked by the central door locking system. <RH drive vehicles>


	COMMENTS ON TROUBLE SYMPTOM If a door or the tailgate can to be locked or unlocked by the central door locking system, the door lock actuator or the tailgate lock actuator may be defective.
	POSSIBLE CAUSES Malfunction of the door lock actuator Malfunction of the tailgate lock actuator Damaged harness wires and connectors
	DIAGNOSIS PROCEDURE

	Step 1. Confirm which door lock actuator is defective. Q: Which door fails to lock correctly? Driver's door: Go to Step 2 . Front passenger's door: Go to Step 6. Rear right door: Go to Step 10. Rear left door: Go to Step 14. Tailgate: Go to Step 18.
	Step 2. Connector check: E-25 driver's door lock actuator connector Q: Is the check result normal? YES: Go to Step 3 . NO: Repair the defective connector.
	Step 3. Driver's door lock actuator check Check that the driver's door lock actuator works normally. Refer to GROUP 42 - Door . Q: Is the check result normal? YES: Go to Step 4. NO: Replace the driver's door lock actuator.
	Step 4. Connector check: C-217, C-220 ETACS-ECU connector Q: Is the check result normal? YES: Go to Step 5 . NO: Repair the defective connector.
	Step 5. Check the wiring harness from C-217 ETACS-ECU connector terminal No.12 and C-220 ETACS-ECU connector No.22 to E-25 driver's door lock actuator connector terminal Nos.4 and 6. NOTE: Prior to the wiring harness inspection, check intermediate connector C-15 and junction block connector C-205, and repair if necessary. Check the input and output lines for open circuit. Q: Is the check result normal? YES: The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ). NO: Repair the wiring harness.
	Step 6. Connector check: E-11 front passenger's door lock actuator connector Q: Is the check result normal? YES: Go to Step 7 . NO: Repair the defective connector.
	Step 7. Check the front passenger's door lock actuator. Check that the front passenger's door lock actuator works normally. Refer to GROUP 42 - Door . Q: Is the check result normal? YES: Go to Step 8. NO: Replace the front passenger's door lock actuator.
	Step 8. Connector check: C-217 ETACS-ECU connector Q: Is the check result normal? YES: Go to Step 9 . NO: Repair the defective connector.
	Step 9. Check the wiring harness from C-217 ETACS-ECU connector terminal Nos.12 and 13 to E-11 front passenger's door lock actuator connector terminal Nos.6 and 4. NOTE: Prior to the wiring harness inspection, check intermediate connector C-34 and junction block connector C-205, and repair if necessary. Check the input and output lines for open circuit. Q: Is the check result normal? YES: The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ). NO: Repair the wiring harness.
	Step 10. Connector check: E-28 rear door lock actuator (RH) connector Q: Is the check result normal? YES: Go to Step 11 . NO: Repair the defective connector.
	Step 11. Check the rear door lock actuator (RH). Check that the rear door lock actuator (RH) is in good condition. Refer to GROUP 42 - Door . Q: Is the check result normal? YES: Go to Step 12. NO: Replace the rear door lock actuator (RH).
	Step 12. Connector check: C-217 ETACS-ECU connector Q: Is the check result normal? YES: Go to Step 13 . NO: Repair the defective connector.
	Step 13. Check the wiring harness from C-217 ETACS-ECU connector terminal Nos.12 and 13 to E-28 rear door lock actuator (RH) connector terminal Nos.2 and 3. NOTE: Prior to the wiring harness inspection, check D-01 intermediate connector and C-221 junction block connector, and repair if necessary. Check the input and output lines for open circuit. Q: Is the check result normal? YES: The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ). NO: Repair the wiring harness.
	Step 14. Connector check: E-08 rear door lock actuator (LH) connector Q: Is the check result normal? YES: Go to Step 15 . NO: Repair the defective connector.
	Step 15. Check the rear door lock actuator (LH). Check that the rear door lock actuator (LH) is in good condition. Refer to GROUP 42 - Door . Q: Is the check result normal? YES: Go to Step 16. NO: Replace the rear door lock actuator (LH).
	Step 16. Connector check: C-217 ETACS-ECU connector Q: Is the check result normal? YES: Go to Step 17 . NO: Repair the defective connector.
	Step 17. Check the wiring harness from C-217 ETACS-ECU connector terminal Nos.12 and 13 to E-08 rear door lock actuator (LH) connector terminal Nos.3 and 2. NOTE: Prior to the wiring harness inspection, check intermediate connectors C-117 and D-26 and junction block connector C-205, and repair if necessary. Check the input and output lines for open circuit. Q: Is the check result normal? YES: The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ). NO: Repair the wiring harness.
	Step 18. Connector check: F-06 tailgate lock actuator connector Q: Is the check result normal? YES: Go to Step 19 . NO: Repair the defective connector.
	Step 19. Check the tailgate lock actuator. Check that the tailgate lock actuator is in good condition. Refer to GROUP 42 - Tailgate . Q: Is the check result normal? YES: Go to Step 20. NO: Replace the tailgate lock actuator.
	Step 20. Connector check: C-217 ETACS-ECU connector Q: Is the check result normal? YES: Go to Step 21 . NO: Repair the defective connector.
	Step 21. Check the wiring harness from C-217 ETACS-ECU connector terminal Nos.12 and 13 to F-06 tailgate lock actuator connector terminal Nos.2 and 3. NOTE: Prior to the wiring harness inspection, check intermediate connector F-05 and junction block connector C-221, and repair if necessary. Check the input and output lines for open circuit. Q: Is the check result normal? YES: The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ). NO: Repair the wiring harness.

PRINT PAGE / INDEX / PRIOR / NEXT