[54D] SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR <Except for Hong Kong spec.> - - SYMPTOM PROCEDURES - POWER WINDOWS - INSPECTION PROCEDURE D-1: Power windows do not work at all. <except vehicles for Argentina>PRINT PAGE / INDEX / PRIOR / NEXT
POWER WINDOWS
INSPECTION PROCEDURE D-1: Power windows do not work at all. <except vehicles for Argentina>
 CAUTION
 Whenever the ECU is replaced, ensure that the input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
If the power windows do not work at all, the power window relay, the power window main switch or the ETACS-ECU may be defective.
POSSIBLE CAUSES
  • Malfunction of the power window relay
  • Malfunction of the power window main switch
  • Malfunction of the ETACS-ECU
  • Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
Step 1. Connector check: C-208 power window relay connector
Q: Is the check result normal?
YES:  Go to Step 2.
NO:  Repair the connector.
Step 2. Check the power window relay.
Refer to GROUP 42 - Door - On-vehicle Service .
Q: Is the check result normal?
YES:  Go to Step 3.
NO:  Replace the power window relay.
Step 3. Connector check: E-05 power window main switch connector
Q: Is the check result normal?
YES:  Go to Step 4.
NO:  Repair the connector.
Step 4. Check the power window main switch.
Refer to GROUP 42 - Door .
Q: Is the check result normal?
YES <RH drive vehicles>:  Go to Step 5.
YES <LH drive vehicles>:  Go to Step 15.
NO:  Replace the power window main switch.
Step 5. Measure the voltage at the E-05 power window main switch connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Turn the ignition switch to the ON position.
  1. Voltage between terminal 13 and body earth
    2. OK: Battery positive voltage
Q: Is the check result normal?
YES:  Go to Step 9.
NO:  Go to Step 6.
Step 6. Check the wiring harness between C-208 power window relay connector terminal No.4 and E-05 power window main switch connector terminal No.13.
NOTE: Prior to the wiring harness inspection, check intermediate connectors C-15, E-29 and junction block connector C-203, and repair if necessary.
  • Check the power supply line for open circuit.
Q: Is the check result normal?
YES:  Go to Step 7.
NO:  Repair the harness wire, and then go to Step 7.
Step 7. Measure the voltage at C-208 power window relay connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Turn the ignition switch to the ON position.
  1. Voltage between terminal 5 and body earth
    2. OK: Battery positive voltage
Q: Is the check result normal?
YES:  Go to Step 9.
NO:  Go to Step 8.
Step 8. Check the wiring harness between C-208 power window relay connector terminal No.5 and fusible link (5).
NOTE: Prior to the wiring harness inspection, check intermediate connectors A-14, C-126 and junction block connector C-203, and repair if necessary.
  • Check the power supply line for open circuit.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
NO:  Repair the wiring harness.
Step 9. Measure the resistance at the E-05 power window main switch connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Resistance between terminal 12 and body earth
    2. OK: 2Ω or less
Q: Is the check result normal?
YES:  Go to Step 11.
NO:  Go to Step 10.
Step 10. Check the wiring harness between E-05 power window main switch connector terminal No.12 and body earth.
NOTE: Prior to the wiring harness inspection, check intermediate connectors C-15 and E-29, and repair if necessary.
  • Check the earth wires for open circuit.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
NO:  Repair the wiring harness.
Step 11. Measure the resistance at C-208 power window relay connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Resistance between terminal 3 and body earth
    2. OK: 2Ω or less
Q: Is the check result normal?
YES:  Go to Step 13.
NO:  Go to Step 12.
Step 12. Check the wiring harness between C-208 power window relay connector terminal No.3 and body earth.
NOTE: Prior to the wiring harness inspection, check junction block connector C-205, and repair if necessary.
  • Check the earth wires for open circuit.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
NO:  Repair the wiring harness.
Step 13. Connector check: C-217 ETACS-ECU connector
Q: Is the check result normal?
YES:  Go to Step 14.
NO:  Repair the connector.
Step 14. Retest the system.
Check that the all the power windows work.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
NO:  Replace the ETACS-ECU.
Step 15. Measure the voltage at the E-05 power window main switch connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Turn the ignition switch to the ON position.
  1. Voltage between terminal 13 and body earth
    2. OK: Battery positive voltage
Q: Is the check result normal?
YES:  Go to Step 19.
NO:  Go to Step 16.
Step 16. Check the wiring harness between C-208 power window relay connector terminal No.4 and E-05 power window main switch connector terminal No.13.
NOTE: Prior to the wiring harness inspection, check intermediate connectors C-118, E-12 and junction block connector C-203, and repair if necessary.
  • Check the power supply line for open circuit.
Q: Is the check result normal?
YES:  Go to Step 19.
NO:  Repair the harness wire, and then go to Step 17.
Step 17. Measure the voltage at C-208 power window relay connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Turn the ignition switch to the ON position.
  1. Voltage between terminal 5 and body earth
    2. OK: Battery positive voltage
Q: Is the check result normal?
YES:  Go to Step 19.
NO:  Go to Step 18.
Step 18. Check the wiring harness between C-208 power window relay connector terminal No.5 and fusible link (5).
NOTE: Prior to the wiring harness inspection, check intermediate connector C-116 and junction block connector C-203, and repair if necessary.
  • Check the power supply line for open circuit.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
NO:  Repair the wiring harness.
Step 19. Measure the resistance at the E-05 power window main switch connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Resistance between terminal 12 and body earth
    2. OK: 2Ω or less
Q: Is the check result normal?
YES:  Go to Step 21.
NO:  Go to Step 20.
Step 20. Check the wiring harness between E-05 power window main switch connector terminal No.12 and body earth.
NOTE: Prior to the wiring harness inspection, check intermediate connectors C-118 and E-12, and repair if necessary.
  • Check the earth wires for open circuit.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
NO:  Repair the wiring harness.
Step 21. Measure the resistance at C-208 power window relay connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Resistance between terminal 3 and body earth
    2. OK: 2Ω or less
Q: Is the check result normal?
YES:  Go to Step 23.
NO:  Go to Step 22.
Step 22. Check the wiring harness between C-208 power window relay connector terminal No.3 and body earth.
NOTE: Prior to the wiring harness inspection, check junction block connector C-205, and repair if necessary.
  • Check the earth wires for open circuit.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
NO:  Repair the wiring harness.
Step 23. Connector check: C-217 ETACS-ECU connector
Q: Is the check result normal?
YES:  Go to Step 24.
NO:  Repair the connector.
Step 24. Retest the system.
Check that the all the power windows work.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
NO:  Replace the ETACS-ECU.
[54D] SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR <Except for Hong Kong spec.> - - SYMPTOM PROCEDURES - POWER WINDOWS - INSPECTION PROCEDURE D-1: Power windows do not work at all. <except vehicles for Argentina>PRINT PAGE / INDEX / PRIOR / NEXT
©2004 Mitsubishi Motors Corporation