[54E] SMART WIRING SYSTEM (SWS) USING SWS MONITOR <Except for Hong Kong spec.> - - INPUT SIGNAL PROCEDURES - INSPECTION PROCEDURE P-9: When the sunroof switch is operated, the switch signals are not received.PRINT PAGE / INDEX / PRIOR / NEXT
INSPECTION PROCEDURE P-9: When the sunroof switch is operated, the switch signals are not received.
 CAUTION
 Whenever the ECU is replaced, ensure that the input signal circuit is normal.
COMMENTS ON TROUBLE SYMPTOM
If the input signal from the sunroof switch is abnormal, the sunroof input check response signal will not be sent to the SWS communication line.
POSSIBLE CAUSES
  • Malfunction of the sunroof motor assembly
  • Malfunction of the sunroof switch
  • Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
Step 1. ECU check by using the SWS monitor
Check that the power supply and earth lines to the sunroof-ECU and the SWS communication lines are normal.
  • Ignition switch: ON
ECUS TO BE CHECKED
  • SUNROOF ECU
OK: "OK" is displayed on the "SUNROOF ECU" menu.
Q: Is the check result normal?
YES:  Go to Step 2.
NO:  Refer to Inspection Procedure A-6 "Communication with sunroof motor assembly (sunroof-ECU) is not possible ."
Step 2. Connector check: D-06 sunroof switch connector
Q: Is the check result normal?
YES:  Go to Step 3.
NO:  Repair the defective connector.
Step 3. Check the sunroof switch.
Q: Is the sunroof switch in good condition? (Refer to GROUP 42 - Sunroof ).
YES:  Go to Step 4.
NO:  Replace the sunroof switch.
Step 4. Measure the resistance at the D-06 sunroof switch connector.
  1. Disconnect the connector, and measure at the wiring harness side.
  1. Continuity between D-06 sunroof switch connector terminal No.4 and body earth
    2. OK: 2Ω or less
Q: Is the check result normal?
YES:  Go to Step 6.
NO:  Go to Step 5.
Step 5. Check the wiring harness between D-06 sunroof motor switch connector terminal No.4 and body earth.
NOTE: Prior to the wiring harness inspection, check intermediate connector C-218 <R.H. drive vehicles>, and repair if necessary.
  • Check the earth wires for open circuit.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
NO:  Repair the wiring harness.
Step 6. Connector check: D-09 sunroof motor assembly connector
Q: Is the check result normal?
YES:  Go to Step 7.
NO:  Repair the defective connector.
Step 7. Check the wiring harness from D-09 sunroof motor assembly connector (terminals 6, 7 and 8) to D-06 sunroof switch connector (terminals 6, 3 and 5).
  • Check the input line for open circuit.
Q: Is the check result normal?
YES:  Go to Step 8.
NO:  Repair the wiring harness.
Step 8. SWS monitor data list
<Selected item> Fr-ECU, P/W, S/R
  • Operate the sunroof switch.
Item No.
 Item name
 Normal condition
Item 72
 Sunroof ECU response
 INPUT CHECK

OK: Normal conditions are displayed for all the positions of the switch.
Q: Is the check result normal?
YES:  The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
NO:  Replace the sunroof motor assembly.
[54E] SMART WIRING SYSTEM (SWS) USING SWS MONITOR <Except for Hong Kong spec.> - - INPUT SIGNAL PROCEDURES - INSPECTION PROCEDURE P-9: When the sunroof switch is operated, the switch signals are not received.PRINT PAGE / INDEX / PRIOR / NEXT
©2004 Mitsubishi Motors Corporation