[54E] SMART WIRING SYSTEM (SWS) USING SWS MONITOR <Except for Hong Kong spec.> - - TROUBLESHOOTING - DATA LIST CHECKPRINT PAGE / INDEX / PRIOR / NEXT
DATA LIST CHECK
  1. Use the MUT-II/III and the SWS monitor to check "DATA LIST." This "DATA LIST" check is applicable for signals, which are transmitted and received through the SWS communication line and the communication lines routed from one door to another. For the input signals which are not applicable for the SWS monitor check, refer to pulse check procedure .
    2. NOTE: If a problem is found in the "DATA LIST" check, refer to the Problems during Input Signal Check <Service data, function diagnosis or pulse check> (Refer to ).
  1. The following input signals can be checked by using the MUT-II/III and the SWS monitor.
DATA LIST REFERENCE TABLE
COLUMN SWITCH (COLUMN-ECU)
Item No.
 Check item
 Display on MUT-II/III
 Check condition
 Normal condition
00
 Headlamp switch
 HEADLAMP SW
 Lighting switch: HEAD
 ON
Lighting switch: Other than HEAD
 OFF
01
 Tail lamp switch
 TAIL LAMP SW
 Lighting switch: TAIL
 ON
Lighting switch: OFF
 OFF
02
 Dimmer switch
 DIMMER SW
 Dimmer switch: ON
 ON
Dimmer switch: OFF
 OFF
03
 Passing lamp switch
 PASSING SW
 Passing lamp which: ON
 ON
Passing lamp which: OFF
 OFF
05
 Windshield intermittent wiper switch
 INT WIPER SW
 Wiper switch: INT
 ON
Wiper switch: Other than INT
 OFF
06
 Windshield low-speed wiper switch
 LO WIPER SW
 Wiper switch: LO
 ON
Wiper switch: Other than LO
 OFF
07
 Windshield high-speed wiper switch
 HI WIPER SW
 Wiper switch: HI
 ON
Wiper switch: Other than HI
 OFF
08
 Wind shield mist wiper switch
 MIST WIPER SW
 Wiper switch: Mist
 ON
Wiper switch: Other than mist
 OFF
09
 Windshield washer switch
 FRONT WASH. SW
 Windshield washer switch: ON
 ON
Windshield washer switch: OFF
 OFF
10
 Turn-signal lamp switch (RH)
 TURN SIG. RH
 Turn-signal lamp switch: RH
 ON
Turn-signal lamp switch: Other than RH
 OFF
11
 Turn-signal lamp switch (LH)
 TURN SIG. LH
 Turn-signal lamp switch: LH
 ON
Turn-signal lamp switch: Other than LH
 OFF
13
 Rear wiper switch
 REAR WIPER SW
 Rear wiper switch: INT
 ON
Rear wiper switch: Other than INT
 OFF
14
 Rear washer switch
 REAR WASH. SW
 Rear wiper switch: Washer
 ON
Rear wiper switch: Other than washer
 OFF
15
 With or without windshield intermittent wiper control
 INT WIP KNOB
 Vehicles with intermittent wiper control
 EQUIP
Vehicles without intermittent wiper control
 NONE
ETACS-ECU
Item No.
 Check item
 Display on MUT-II/III
 Check condition
 Normal condition
30
 Ignition switch (IG1)
 IG SW(IG1)
 Ignition switch: ON or START
 ON
Ignition switch: LOCK (OFF) or ACC
 OFF
31
 Ignition switch (ACC)
 IG SW(ACC)
 Ignition switch: ACC or ON
 ON
Ignition switch: LOCK (OFF) or START
 OFF
32
 Driver's door switch*1
DR DOOR SW
 Driver's door switch ON (The driver’s door is open).
 ON
Driver's door switch OFF (The driver's door is closed).
 OFF
Front door switch*2
FRONT DOOR SW
 Front door switch: ON (front door open)
 ON
Front door switch: OFF (front door closed)
 OFF
33
 Reception of power window switch
 P/W SW ACCEPT
 Ignition switch: ON or START
 PERMIT
Ignition switch: from ON or START to LOCK (OFF) or ACC
 from PERMIT to PROHIBIT (after approximately 30 seconds)
34
 Multimode keyless entry system
 KEYLESS ENTRY
  1. Keyless entry transmitter LOCK switch: ON
  1. Turn ON the keyless entry transmitter LOCK switch again (For the second switch operation, hold pressing the switch for at least one second within 30 seconds after the switch is turned on at first)
 MULTI CLOSE (only momentarily when switch is operated)
  1. Keyless entry transmitter UNLOCK switch: ON
  1. Turn ON the keyless entry transmitter UNLOCK switch again (For the second switch operation, hold pressing the switch for at least one second within 30 seconds after the switch is turned on at first)
 MULTI OPEN (only momentarily when switch is operated)
  1. When multimode is working
  1. Turn on any function of the keyless entry transmitter again.
 MULTI STOP (only momentarily when switch is operated)
Other than the conditions above
 WAITING
35
 Headlamp automatic shutdown function
 HD AUTO-CUT
  1. Lighting switch: Other than OFF
  1. Ignition switch: from ON or START to LOCK (OFF) or ACC
  1. Driver's door switch: ON (driver's door open)
 OFF to ON (after approximately one second)
When requirements for the headlamp automatic shutdown are not satisfied
 OFF
36
 Request of fog lamp illumination
 F.FOG LAMP
  1. Lighting switch: "TAIL" or "HEAD"
  1. Fog lamp switch: ON
 ON
Other than the conditions above
 OFF
37
 Windshield intermittent wiper interval
 INT WIPE TIME
  1. Ignition switch: ACC or ON
  1. Operate the intermittent wiper control, and change the wiper interval
 The MUT-II/III displays intermittent wiper interval in response to the intermittent wiper control positions
41
 Park/neutral switch ("R" position)
 INHIBITOR SW
 Park/neutral switch: "R" position
 ON
Park/neutral switch: Other than "R" position
 OFF
43
 Buzzer
 BUZZER
  1. Ignition switch: LOCK (OFF)
  1. Key reminder switch: ON
  1. Driver's door switch: ON (driver's door open)
 ON
When requirements for sounding each warning buzzer are not satisfied
 OFF
NOTE: 
  1. For item number 43, the MUT-II/III also displays "ON" when the lamp reminder buzzer or R (reverse) position warning buzzer is triggered.
  1. *1 : Except for Australia
  1. *2 : Vehicles for Australia
FRONT-ECU
Item No.
 Check item
 Display on MUT-II/III
 Check condition
 Normal condition
70
 Response by the front-ECU
 Front ECU response
 Lighting switch: Other than OFF (excluding when high-beam is on) or the wiper switch is at position other than OFF
 Normal response
  • Ignition switch: ON or START
  • Lighting switch: OFF
  • Wiper switch: OFF
 SLEEP RESPONSE
  • Lighting switch: HEAD
  • Headlamps: at high beam
 HI BEAM RESPONSE
-
 No response
NOTE: For item number 70, the MUT-II/III also displays "NG" under the "ECU Check" when it displays "No response" under the front-ECU check.
POWER WINDOW MAIN SWITCH (POWER WINDOW MODULE) <VEHICLES FOR ARGENTINA ONLY>
Item No.
 Check item
 Display on MUT-II/III
 Check condition
 Normal condition
71
 Response from power window module
 P/W ECU ACK
 Ignition switch: ON or START
 NORMAL ACK
  1. Ignition switch: ON or START
  1. Operate any switch of the power window main switch.
 INPUT CHECK (only momentarily when switch is operated)
-
 NO ACK
NOTE: For item number 71, the MUT-II/III also displays "NG" under the "ECU CHECK" when it displays "NO ACK" under the "P/W ECU ACK" check.
SUNROOF MOTOR ASSEMBLY (SUNROOF-ECU)
Item No.
 Check item
 Display on MUT-II/III
 Check condition
 Normal condition
72
 Response by the sunroof-ECU
 S/R ECU ACK
  1. Ignition switch: ON or START
  1. While sunroof is off
 NORMAL ACK → SLEEP ACK (after approximately 30 seconds)
  1. Ignition switch: ON or START
  1. One of the sunroof switches is on
 INPUT CHECK → NORMAL ACK
-
 NO ACK
NOTE: For item number 72, the MUT-II/III also displays "NG" under the "ECU CHECK" when it displays "NO ACK" under the "S/R ECU ACK" check.
FUNCTION DIAGNOSIS
The table below shows the service data and their normal condition, which are displayed during the "FUNCTION DIAG." The row "Normal conditions" shows values, which are shown when each operation is made.
WIPER
ITEM
 Input signal
 Item No.
 Display on MUT-II/III
 Normal condition
F.WIPER INT (intermittent)
 Windshield intermittent wiper switch
 05
 INT WIPER SW
 ON
Windshield low-speed wiper switch
 06
 LO WIPER SW
 OFF
Windshield high-speed wiper switch
 07
 HI WIPER SW
 OFF
Wind shield mist wiper switch
 08
 MIST WIPER SW
 OFF
Windshield washer switch
 09
 FRONT WASH. SW
 OFF
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
Windshield intermittent wiper interval
 37
 WIPER INT TIME
 The MUT-II/III displays intermittent wiper interval in response to the intermittent wiper control positions
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
F.WIPER LO (low speed)
 Windshield intermittent wiper switch
 05
 INT WIPER SW
 OFF
Windshield low-speed wiper switch
 06
 LO WIPER SW
 ON
Windshield high-speed wiper switch
 07
 HI WIPER SW
 OFF
Wind shield mist wiper switch
 08
 MIST WIPER SW
 OFF
Windshield washer switch
 09
 FRONT WASH. SW
 OFF
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
F.WIPER HI (high speed)
 Windshield intermittent wiper switch
 05
 INT WIPER SW
 OFF
Windshield low-speed wiper switch
 06
 LO WIPER SW
 OFF
Windshield high-speed wiper switch
 07
 HI WIPER SW
 ON
Wind shield mist wiper switch
 08
 MIST WIPER SW
 OFF
Windshield washer switch
 09
 FRONT WASH. SW
 OFF
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
F.WIPER MIST
 Windshield intermittent wiper switch
 05
 INT WIPER SW
 OFF
Windshield low-speed wiper switch
 06
 LO WIPER SW
 OFF
Windshield high-speed wiper switch
 07
 HI WIPER SW
 OFF
Wind shield mist wiper switch
 08
 MIST WIPER SW
 ON
Windshield washer switch
 09
 FRONT WASH. SW
 OFF
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
F.WIPER WASH
 Wind shield mist wiper switch
 08
 MIST WIPER SW
 OFF
Windshield washer switch
 09
 FRONT WASH. SW
 ON
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
REAR WIPER
ITEM
 Input signal
 Item No.
 Display on MUT-II/III
 Normal condition
REAR WIPER
 Rear wiper switch
 13
 REAR WIPER SW
 ON
Rear washer switch
 14
 REAR WASH. SW
 OFF
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
REV. INTERLOCK
 Rear wiper switch
 13
 REAR WIPER SW
 ON
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
Park/neutral switch ("R" position)
 41
 INHIBITOR SW
 ON
REAR WASHER
 Rear washer switch
 14
 REAR WASH. SW
 ON
Ignition switch (ACC)
 31
 IG SW(ACC)
 ON
LIGHTING
ITEM
 Input signal
 Item No.
 Display on MUT-II/III
 Normal condition
OFF
 Headlamp switch
 00
 HEADLAMP SW
 OFF
Tail lamp switch
 01
 TAIL LAMP SW
 OFF
Passing lamp switch
 03
 PASSING SW
 OFF
Ignition switch (IG1)*
30
 IG SW(IG1)
 ON
Headlamp automatic shutdown function*
35
 HD AUTO-CUT
 OFF
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
TAIL LAMP
 Headlamp switch
 00
 HEADLAMP SW
 OFF
Tail lamp switch
 01
 TAIL LAMP SW
 ON
Passing lamp switch
 03
 PASSING SW
 OFF
Ignition switch (IG1)*
30
 IG SW(IG1)
 ON
Headlamp automatic shutdown function*
35
 HD AUTO-CUT
 OFF
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK
HEADLAMP LO (low-beam)
 Headlamp switch
 00
 HEADLAMP SW
 ON
Passing lamp switch
 03
 PASSING SW
 OFF
Ignition switch (IG1)*
30
 IG SW(IG1)
 ON
Headlamp automatic shutdown function*
35
 HD AUTO-CUT
 OFF
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK
HEADLAMP HI (high-beam)
 Headlamp switch
 00
 HEADLAMP SW
 ON
Dimmer switch
 02
 DIMMER SW
 ON
Ignition switch (IG1)*
30
 IG SW(IG1)
 ON
Headlamp automatic shutdown function*
35
 HD AUTO-CUT
 OFF
Response by the front-ECU
 70
 FRONT ECU ACK
 HI-BEAM ACK
PASSING LAMP
 Passing lamp switch
 03
 PASSING SW
 ON
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
F.FOG LAMP
 Headlamp switch
 00
 HEADLAMP SW
 Either of items is ON
Tail lamp switch
 01
 TAIL LAMP SW
Ignition switch (IG1)*
30
 IG SW(IG1)
 ON
Headlamp automatic shutdown function*
35
 HD AUTO-CUT
 OFF
Request of fog lamp illumination
 36
 F.FOG LAMP
 ON
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK
REAR FOG LAMP
 Headlamp switch
 00
 HEADLAMP SW
 ON
Tail lamp switch
 01
 TAIL LAMP SW
 ON
Headlamp automatic shutdown function*
35
 HD AUTO-CUT
 OFF
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
HD AUTO-CUT*
Headlamp switch
 00
 HEADLAMP SW
 Either is on
Tail lamp switch
 01
 TAIL LAMP SW
Ignition switch (IG1)
 30
 IG SW(IG1)
 OFF
Driver's door switch
 32
 DR DOOR SW
 ON
Headlamp automatic shutdown function
 35
 HD AUTO-CUT
 ON
Response by the front-ECU
 70
 FRONT ECU ACK
 NORMAL ACK or HI-BEAM ACK
NOTE: 
  1. When checking the input signals (off, tail, low-beam or high-beam), turn the ignition switch to the "ON" position in order to disable the headlamp automatic shutdown function. However, the titles on the MUT-II/III screen will not be highlighted as this has nothing to do with actual lamp operation.
  1. For checking item "HEADLAMP HI", the MUT-II/III displays "OFF" on the item No.02 "DIMMER SW" when the headlamps are at high-beam. Therefore, the MUT-II/III should display "ON" momentarily when the dimmer switch is operated.
  1. * : Except for Australia
TURN-SIGNAL LAMP
ITEM
 Input signal
 Item No.
 Display on MUT-II/III
 Normal condition
Turn-signal lamp (RH)
 Turn-signal lamp switch (RH)
 10
 TURN SIGNAL RH SW
 ON
Turn-signal lamp switch (LH)
 11
 TURN SIGNAL LH SW
 OFF
Ignition switch (IG1)
 30
 IGNITION SW IG1
 ON
Turn-signal lamp (LH)
 Turn-signal lamp switch (RH)
 10
 TURN SIGNAL RH SW
 OFF
Turn-signal lamp switch (LH)
 11
 TURN SIGNAL LH SW
 ON
Ignition switch (IG1)
 30
 IGNITION SW IG1
 ON
BUZZER
ITEM
 Input signal
 Item No.
 Display on MUT-II/III
 Normal condition
Lighting monitor buzzer
 Headlamp switch
 00
 HEADLAMP SW
 Either is on
Tail lamp switch
 01
 TAIL LAMP SW
Ignition switch (IG1)
 30
 IGNITION SW IG1
 OFF
Driver's door switch
 32
 DRIVER DOOR SW
 ON
Headlamp automatic shutdown function
 35
 HD LAMP AUTOCUT
 OFF
Buzzer
 43
 BUZZER
 ON
Key reminder buzzer*
Ignition switch (IG1)
 30
 IGNITION SW IG1
 OFF
Driver's door switch
 32
 DRIVER DOOR SW
 ON
Buzzer
 43
 BUZZER
 ON
NOTE: 
  1. The headlamp automatic shutdown function works in approximately one second after the lighting monitor buzzer starts sounding, and then the buzzer ceases sounding.
  1. * : Except for Australia
SUNROOF
ITEM
 Input signal
 Item No.
 Display on MUT-II/III
 Normal condition
SUNROOF OPE.
 Ignition switch (IG1)
 30
 IG SW(IG1)
 ON
Response by power window module
 71
 P/W ECU ACK
 NORMAL ACK
Response by the sunroof-ECU
 72
 S/R ECU ACK
 INPUT CHECK (only momentarily when switch is operated)
[54E] SMART WIRING SYSTEM (SWS) USING SWS MONITOR <Except for Hong Kong spec.> - - TROUBLESHOOTING - DATA LIST CHECKPRINT PAGE / INDEX / PRIOR / NEXT
©2004 Mitsubishi Motors Corporation