SERVICE DATA CHECK

Use the MUT-II/III and the SWS monitor to check "Service Data."
This "Service Data" check is applicable for signals, which are transmitted and received through the SWS communication line and the communication lines routed from one door to another. For the input signals which are not applicable for the SWS monitor check, refer to pulse check procedure .

NOTE: If a problem is found in the "Service Data" check, refer to the Problems during Input Signal Check <Service data, function diagnosis or pulse check> (Refer to

The following input signals can be checked by using the MUT-II/III and the SWS monitor.

SERVICE DATA REFERENCE TABLE

COLUMN SWITCH (COLUMN-ECU)

Item No.	Check items	Display on MUT-II/III	Check conditions	Normal conditions
00	Headlamp switch	HEADLAMP SW	Lighting switch: HEAD	ON
00	Headlamp switch	HEADLAMP SW	Lighting switch: Other than HEAD	OFF
01	Tail lamp switch	TAIL LAMP SW	Lighting switch: TAIL	ON
01	Tail lamp switch	TAIL LAMP SW	Lighting switch: OFF	OFF
02	Dimmer switch	DIMMER SW	Dimmer switch: ON	ON
02	Dimmer switch	DIMMER SW	Dimmer switch: OFF	OFF
03	Passing lamp switch	PASSING SW	Passing lamp which: ON	ON
03	Passing lamp switch	PASSING SW	Passing lamp which: OFF	OFF
05	Windshield intermittent wiper switch	INT WIPER SW	Wiper switch: INT	ON
05	Windshield intermittent wiper switch	INT WIPER SW	Wiper switch: Other than INT	OFF
06	Windshield low-speed wiper switch	LO WIPER SW	Wiper switch: LO	ON
06	Windshield low-speed wiper switch	LO WIPER SW	Wiper switch: Other than LO	OFF
07	Windshield high-speed wiper switch	HI WIPER SW	Wiper switch: HI	ON
07	Windshield high-speed wiper switch	HI WIPER SW	Wiper switch: Other than HI	OFF
08	Wind shield mist wiper switch	MIST WIPER SW	Wiper switch: Mist	ON
08	Wind shield mist wiper switch	MIST WIPER SW	Wiper switch: Other than mist	OFF
09	Windshield washer switch	FRONT WASH. SW	Windshield washer switch: ON	ON
09	Windshield washer switch	FRONT WASH. SW	Windshield washer switch: OFF	OFF
10	Turn-signal lamp switch: RH	TURN SIG. RH	Turn-signal lamp switch: RH	ON
10	Turn-signal lamp switch: RH	TURN SIG. RH	Turn-signal lamp switch: Other than RH	OFF
11	Turn-signal lamp switch (LH)	TURN SIG. LH	Turn-signal lamp switch: LH	ON
11	Turn-signal lamp switch (LH)	TURN SIG. LH	Turn-signal lamp switch: Other than LH	OFF
13	Rear wiper switch	REAR WIPER SW	Rear wiper switch: INT	ON
13	Rear wiper switch	REAR WIPER SW	Rear wiper switch: Other than INT	OFF
14	Rear washer switch	REAR WASH. SW	Rear wiper switch: Washer	ON
14	Rear washer switch	REAR WASH. SW	Rear wiper switch: Other than washer	OFF
15	With or without windshield intermittent wiper control	INT WIP KNOB	Vehicles with intermittent wiper control	EQUIP
15	With or without windshield intermittent wiper control	INT WIP KNOB	Vehicles without intermittent wiper control	NONE

ETACS-ECU

Item No.	Check items	Display on MUT-II/III	Check conditions	Normal conditions
30	Ignition switch (IG1)	IG SW (IG1)	Ignition switch: ON or START	ON
30	Ignition switch (IG1)	IG SW (IG1)	Ignition switch: LOCK (OFF) or ACC	OFF
31	Ignition switch (ACC)	IG SW(ACC)	Ignition switch: ACC or ON	ON
31	Ignition switch (ACC)	IG SW(ACC)	Ignition switch: LOCK (OFF) or START	OFF
32	Driver's door switch	DR DOOR SW	Driver's door switch: ON (driver's door open)	ON
32	Driver's door switch	DR DOOR SW	Driver's door switch: OFF (driver's door close)	OFF
33	Reception of power window switch	P/W SW ACCEPT	Ignition switch: ON or START	PERMIT
33	Reception of power window switch	P/W SW ACCEPT	Ignition switch: from ON or START to LOCK (OFF) or ACC	from PERMIT to PROHIBIT (after approximately 30 seconds)
34	Multimode keyless entry system	KEYLESS ENTRY	Keyless entry transmitter LOCK switch: ON Turn ON the keyless entry transmitter LOCK switch again (For the second switch operation, hold pressing the switch for at least one second within 30 seconds after the switch is turned on at first)	MULTI CLOSE (only momentarily when switch is operated)
			Keyless entry transmitter UNLOCK switch: ON Turn ON the keyless entry transmitter UNLOCK switch again (For the second switch operation, hold pressing the switch for at least one second within 30 seconds after the switch is turned on at first)	MULTI OPEN (only momentarily when switch is operated)
			When multimode is working Turn on any function of the keyless entry transmitter again.	MULTI STOP (only momentarily when switch is operated)
			Other than the conditions above	WAITING
35	Headlamp automatic shutdown function	HD AUTO-CUT	Lighting switch: Other than OFF Ignition switch: from ON or START to LOCK (OFF) or ACC Driver's door switch: ON (driver's door open)	OFF to ON (after approximately one second)
35	Headlamp automatic shutdown function	HD AUTO-CUT	When requirements for the headlamp automatic shutdown are not satisfied	OFF
36	Request of fog lamp illumination	F.FOG LAMP	Lighting switch: "TAIL" or "HEAD" Fog lamp switch: ON	ON
36	Request of fog lamp illumination	F.FOG LAMP	Other than the conditions above	OFF
37	Windshield intermittent wiper interval	INT WIPE TIME	Ignition switch: ACC or ON Operate the intermittent wiper control, and change the wiper interval	The MUT-II/III displays intermittent wiper interval in response to the intermittent wiper control positions
38	All of the door switches	THEFT-ALARM	Either door: open	ON
38	All of the door switches	THEFT-ALARM	All the doors: Closed	OFF
41	Park/neutral switch ("R" position)	INHIBITOR SW	Park/neutral switch: "R" position	ON
41	Park/neutral switch ("R" position)	INHIBITOR SW	Park/neutral switch: Other than "R" position	OFF
42	Activating the wipers when the vehicle starts.	WIPER ON COM.	Wiper switch: INT Drive the vehicle at 7 km/h or more.	EQUIP
42	Activating the wipers when the vehicle starts.	WIPER ON COM.	Other than the conditions above	NONE
43	Buzzer	BUZZER	Ignition switch: LOCK (OFF) Key reminder switch: ON Driver's door switch: ON (driver's door open)	ON
43	Buzzer	BUZZER	When requirements for sounding each warning buzzer are not satisfied	OFF

NOTE: For item number 43, the MUT-II/III also displays "ON" when the lamp reminder buzzer or R (reverse) position warning buzzer is triggered.

FRONT-ECU

Item No.	Check items	Display on MUT-II/III	Check conditions	Normal conditions
70	Response by the front-ECU	FRONT ECU ACK	Lighting switch is at position other than OFF (excluding when high-beam is on) or the wiper switch is at position other than OFF	NORMAL ACK
			Ignition switch: ON or START Lighting switch: OFF Wiper switch: OFF	SLEEP ACK
			Lighting switch: HEAD Headlamp: High-beam	HI-BEAM ACK
			-	NO ACK

NOTE: For item number 70, the MUT-II/III also displays "NG" under the "ECU Check" when it displays "No response" under the front-ECU check.

POWER WINDOW MAIN SWITCH (POWER WINDOW MODULE)

Item No.

Check items

Display on MUT-II/III

Check conditions

Normal conditions

Response from power window module

P/W ECU ACK

Ignition switch: ON or START

NORMAL ACK

Ignition switch: ON or START

Operate any switch of the power window main switch.

INPUT CHECK (only momentarily when switch is operated)

NO ACK

NOTE: For item number 71, the MUT-II/III also displays "NG" under the "ECU Check" when it displays "No response" under the "P/W MODULE RESPONSE" check.

SUNROOF MOTOR ASSEMBLY (SUNROOF-ECU)

Item No.

Check items

Display on MUT-II/III

Check conditions

Normal conditions

Response by the sunroof-ECU

S/R ECU ACK

Ignition switch: ON or START

While sunroof is off

NORMAL ACK → SLEEP ACK (after approximately 30 seconds)

Ignition switch: ON or START

One of the sunroof switches is on

INPUT CHECK → NORMAL ACK

NO ACK

NOTE: For item number 72, the MUT-II/III also displays "NG" under the "ECU Check" when it displays "No response" under the "sunroof-ECU response" check.

COMMUNICATION BETWEEN DOORS

Item No.	Check items	Display on MUT-II/III	Check conditions	Normal conditions
C0	Front passenger's power window UP switch	PASS DOR UP	Front passenger's power window switch: UP	ON
C0	Front passenger's power window UP switch	PASS DOR UP	Front passenger's power window switch: Other than "UP"	OFF
C1	Front passenger's power window DOWN switch	PASS DOR DOWN	Front passenger's power window switch: DOWN	ON
C1	Front passenger's power window DOWN switch	PASS DOR DOWN	Front passenger's power window switch: Other than "DOWN"	OFF
C2	Front passenger's power window AUTO switch	PASS DOR AUTO	Front passenger's power window switch: AUTO	ON
C2	Front passenger's power window AUTO switch	PASS DOR AUTO	Front passenger's power window switch: Other than "AUTO"	OFF
C4	Rear right power window UP switch	REAR RH UP	Rear right power window switch: UP	ON
C4	Rear right power window UP switch	REAR RH UP	Rear right power window switch: Other than "UP"	OFF
C5	Rear right power window DOWN switch	REAR RH DOWN	Rear right power window switch: DOWN	ON
C5	Rear right power window DOWN switch	REAR RH DOWN	Rear right power window switch: Other than "DOWN"	OFF
C6	Rear right power window AUTO switch	REAR RH AUTO	Rear right power window switch: AUTO	ON
C6	Rear right power window AUTO switch	REAR RH AUTO	Rear right power window switch: Other than "AUTO"	OFF
C8	Rear left power window UP switch	REAR LH UP	Rear left power window switch: UP	ON
C8	Rear left power window UP switch	REAR LH UP	Rear left power window switch: Other than "UP"	OFF
C9	Rear left power window DOWN switch	REAR LH DOWN	Rear left power window switch: DOWN	ON
C9	Rear left power window DOWN switch	REAR LH DOWN	Rear left power window switch: Other than "DOWN"	OFF
CA	Rear left power window AUTO switch	REAR LH AUTO	Rear left power window switch: AUTO	ON
CA	Rear left power window AUTO switch	REAR LH AUTO	Rear left power window switch: Other than "AUTO"	OFF
CB	Power window lock switch	P/W LOCK SW	Power window lock switch: ON	ON
CB	Power window lock switch	P/W LOCK SW	Power window lock switch: OFF	OFF
CD	Multi-stop	MLT-MODE STOP	When multimode is working Either function of keyless entry transmitter: ON	ON (only momentarily when switch is operated)
CD	Multi-stop	MLT-MODE STOP	Other than the conditions above	OFF
CE	Reception of power window switch	P/W SW RECEPT	Ignition switch: ON or START	PERMIT
CE	Reception of power window switch	P/W SW RECEPT	Ignition switch: from ON or START to LOCK (OFF) or ACC	from PERMIT to PROHIBIT (after approximately 30 seconds)
CF	Ignition switch (IG1)	IG1	Ignition switch: ON or START	ON
CF	Ignition switch (IG1)	IG1	Ignition switch: LOCK (OFF) or ACC	OFF

NOTE: Service data of door communication will be sent from the power window main switch to the door communication line. Therefore, the display will remain "OFF" unless the probe is inserted.

FUNCTION DIAGNOSIS

The table below shows the service data and their normal condition, which are displayed during the "FUNCTION DIAGNOSIS." The row "Normal conditions" shows values, which are shown when each operation is made.

WIPER

ITEM	Input signals	Item No.	Display on MUT-II/III	Normal conditions
F.WIPER INT (intermittent)	Windshield intermittent wiper switch	05	INT WIPER SW	ON
	Windshield low-speed wiper switch	06	LO WIPER SW	OFF
	Windshield high-speed wiper switch	07	HI WIPER SW	OFF
	Wind shield mist wiper switch	08	MIST WIPER SW	OFF
	Windshield washer switch	09	FRONT WASHER SW	OFF
	Ignition switch (ACC)	31	IGNITION SW ACC	ON
	Windshield intermittent wiper interval	37	WIPER INT TIME	The MUT-II/III displays intermittent wiper interval in response to the intermittent wiper control positions
	Response by the front-ECU	70	Front ECU response	Normal response or high beam response
F.WIPER LO (low speed)	Windshield intermittent wiper switch	05	INT WIPER SW	OFF
	Windshield low-speed wiper switch	06	LO WIPER SW	ON
	Windshield high-speed wiper switch	07	HI WIPER SW	OFF
	Wind shield mist wiper switch	08	MIST WIPER SW	OFF
	Windshield washer switch	09	FRONT WASH. SW	OFF
	Ignition switch (ACC)	31	IG SW(ACC)	ON
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK or HI-BEAM ACK
F.WIPER HI (high speed)	Windshield intermittent wiper switch	05	INT WIPER SW	OFF
	Windshield low-speed wiper switch	06	LO WIPER SW	OFF
	Windshield high-speed wiper switch	07	HI WIPER SW	ON
	Wind shield mist wiper switch	08	MIST WIPER SW	OFF
	Windshield washer switch	09	FRONT WASH. SW	OFF
	Ignition switch (ACC)	31	IG SW(ACC)	ON
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK or HI-BEAM ACK
F.WIPER MIST	Windshield intermittent wiper switch	05	INT WIPER SW	OFF
	Windshield low-speed wiper switch	06	LO WIPER SW	OFF
	Windshield high-speed wiper switch	07	HI WIPER SW	OFF
	Wind shield mist wiper switch	08	MIST WIPER SW	ON
	Windshield washer switch	09	FRONT WASH. SW	OFF
	Ignition switch (ACC)	31	IG SW(ACC)	ON
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK or HI-BEAM ACK
F.WIPER WASH	Wind shield mist wiper switch	08	MIST WIPER SW	OFF
	Windshield washer switch	09	FRONT WASH. SW	ON
	Ignition switch (ACC)	31	IG SW(ACC)	ON
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK or HI-BEAM ACK

REAR WIPER

Items	Input signals	Item No.	Display on MUT-II/III	Normal conditions
REAR WIPER	Rear wiper switch	13	REAR WIPER SW	ON
	Rear washer switch	14	REAR WASH. SW	OFF
	Ignition switch (ACC)	31	IG SW(ACC)	ON
REV.INTERLOCK	Rear wiper switch	13	REAR WIPER SW	ON
	Ignition switch (ACC)	31	IGNITION SW ACC	ON
	Park/neutral switch ("R" position)	41	INHIBITOR SW	ON
REAR WASHER	Rear washer switch	14	REAR WASH. SW	ON
REAR WASHER	Ignition switch (ACC)	31	IG SW(ACC)	ON

LIGHTING

Items	Input signals	Item No.	Display on MUT-II/III	Normal conditions
OFF	Headlamp switch	00	HEADLAMP SW	OFF
	Tail lamp switch	01	TAIL LAMP SW	OFF
	Passing lamp switch	03	PASSING SW	OFF
	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Headlamp automatic shutdown function	35	HD AUTO-CUT	OFF
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK or HI-BEAM ACK
TAIL LAMP	Headlamp switch	00	HEADLAMP SW	OFF
	Tail lamp switch	01	TAIL LAMP SW	ON
	Passing lamp switch	03	PASSING SW	OFF
	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Headlamp automatic shutdown function	35	HD AUTO-CUT	OFF
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK
HEADLAMP LO (low-beam)	Headlamp switch	00	HEADLAMP SW	ON
	Dimmer switch	02	DIMMER SW	OFF
	Passing lamp switch	03	PASSING SW	OFF
	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Headlamp automatic shutdown function	35	HD AUTO-CUT	OFF
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK
HEADLAMP HI (high-beam)	Headlamp switch	00	HEADLAMP SW	ON
	Dimmer switch	02	DIMMER SW	ON
	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Headlamp automatic shutdown function	35	HD AUTO-CUT	OFF
	Response by the front-ECU	70	FRONT ECU ACK	HI-BEAM ACK
PASSING LAMP	Passing lamp switch	03	PASSING SW	ON
PASSING LAMP	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK or HI-BEAM ACK
F.FOG LAMP	Headlamp switch	00	HEADLAMP SW	Either of items is ON
	Tail lamp switch	01	TAIL LAMP SW	Either of items is ON
	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Headlamp automatic shutdown function	35	HD AUTO-CUT	OFF
	Request of fog lamp illumination	36	F.FOG LAMP	ON
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK
HD AUTO-CUT	Headlamp switch	00	HEADLAMP SW	Either is ON
	Tail lamp switch	01	TAIL LAMP SW	Either is ON
	Ignition switch (IG1)	30	IG SW (IG1)	OFF
	Driver's door switch	32	DR DOOR SW	ON
	Headlamp automatic shutdown function	35	HD AUTO-CUT	ON
	Response by the front-ECU	70	FRONT ECU ACK	NORMAL ACK or HI-BEAM ACK

NOTE: When checking the input signals (off, tail, low-beam or high-beam), turn the ignition switch to the "ON" position in order to disable the headlamp automatic shutdown function. However, the titles on the MUT-II/III screen will not be highlighted as this has nothing to do with actual lamp operation.
For checking item "HI (High-beam)", the MUT-II/III displays "OFF" on the item No.2 "Dimmer SW" when the headlamps are at high-beam. Therefore, the MUT-II/III should display "ON" momentarily when the dimmer switch is operated.

TURN SIGNAL LAMP

Items	Input signals	Item No.	Display on MUT-II/III	Normal conditions
TURN-SIG.RH	Turn-signal lamp switch (RH)	10	TURN SIG. RH	ON
	Turn-signal lamp switch (LH)	11	TURN SIG. LH	OFF
	Ignition switch (IG1)	30	IG SW (IG1)	ON
TURN-SIG.LH	Turn-signal lamp switch (RH)	10	TURN SIG. RH	OFF
	Turn-signal lamp switch (LH)	11	TURN SIG. LH	ON
	Ignition switch (IG1)	30	IG SW (IG1)	ON

BUZZER

Items	Input signals	Item No.	Display on MUT-II/III	Normal conditions
LGT MONI.ALRM	Headlamp switch	00	HEADLAMP SW	Either is on
	Tail lamp switch	01	TAIL LAMP SW	Either is on
	Ignition switch (IG1)	30	IG SW (IG1)	OFF
	Driver's door switch	32	DR DOOR SW	ON
	Headlamp automatic shutdown function	35	HD AUTO-CUT	OFF
	Buzzer	43	BUZZER	ON
KEY REMND.ALM	Ignition switch (IG1)	30	IG SW (IG1)	OFF
	Driver's door switch	32	DR DOOR SW	ON
	Buzzer	43	BUZZER	ON
REVERSE ALRM	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Park/neutral switch ("R" position)	41	INHIBITOR SW	ON
	Buzzer	43	BUZZER	ON

NOTE: The headlamp automatic shutdown function works in approximately one second after the lighting monitor buzzer starts sounding, and then the buzzer ceases sounding.

POWER WINDOWS

Items	Input signals	Item No.	Display on MUT-II/III	Normal conditions
POWER WINDOW	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Reception of power window switch	33	P/W SW ACCEPT	PERMIT
	Response by power window module	71	P/W ECU ACK	INPUT CHECK (only momentarily when switch is operated)

KEYLESS ENTRY SYSTEM

Items	Input signals	Item No.	Display on MUT-II/III	Normal conditions
MULTI STOP	Reception of power window switch	33	P/W SW ACCEPT	PERMIT
	Multimode keyless entry system	34	KEYLESS ENTRY	MULTI STOP (only momentarily when switch is operated)
	Response by power window module	71	P/W ECU ACK	NORMAL ACK OR P/W LOCK ACK
MULTI OPEN	Reception of power window switch	33	P/W SW ACCEPT	PERMIT
	Multimode keyless entry system	34	KEYLESS ENTRY	MULTI OPEN (only momentarily when switch is operated)
	Response by power window module	71	P/W ECU ACK	NORMAL ACK OR P/W LOCK ACK
MULTI CLOSE	Reception of power window switch	33	P/W SW ACCEPT	PERMIT
	Multimode keyless entry system	34	KEYLESS ENTRY	MULTI CLOSE (only momentarily when switch is operated)
	Response by power window module	71	P/W ECU ACK	NORMAL ACK OR P/W LOCK ACK
	Response by the sunroof-ECU	72	S/R ECU ACK	NORMAL ACK

SUNROOF

Items	Input signals	Item No.	Display on MUT-II/III	Normal conditions
SUNROOF OPE.	Ignition switch (IG1)	30	IG SW (IG1)	ON
	Response by power window module	71	P/W ECU ACK	NORMAL ACK
	Response by the sunroof-ECU	72	S/R ECU ACK	INPUT CHECK (only momentarily when switch is operated)

ETACS SWITCH DATA CHART

Item No.	Check items	Display on MUT-II/III	Check conditions	Normal conditions
01	Specification switching terminal	SPEC. SW 1	-	A/T
03	Key reminder switch	KEY REMIN SW	Key reminder switch: ON (when the ignition key is pulled off)	ON
03	Key reminder switch	KEY REMIN SW	Key reminder switch: OFF (when the ignition key is inserted)	OFF
04	Hazard warning lamp switch	HAZARD LMP SW	Hazard warning lamp switch: ON (when the switch is operated)	ON
04	Hazard warning lamp switch	HAZARD LMP SW	Hazard warning lamp switch: ON (when the switch is not operated)	OFF
09	Rear wiper auto-stop switch	R.WIPE A/STOP	When rear wiper is operating	ON
09	Rear wiper auto-stop switch	R.WIPE A/STOP	When the rear wiper is not working	OFF
10	Fog lamp switch	F.FOG LAMP SW	Fog lamp switch: ON (when the switch is operated)	ON
10	Fog lamp switch	F.FOG LAMP SW	Fog lamp switch: ON (when the switch is not operated)	OFF
13	Hood switch	HOOD SW	Hood switch: ON (hood open)	ON
13	Hood switch	HOOD SW	Hood switch: OFF (hood closed)	OFF
14	Electric remote-controlled door mirror (folding/unfolding ) switch	EL RET MIR SW	Electric remote-controlled door mirror (folding/unfolding ) switch: ON (when the switch is operated)	ON
14		EL RET MIR SW	Electric remote-controlled door mirror (folding/unfolding ) switch: ON (when the switch is not operated)	OFF
20	Impact sensor	IMPACT SENSOR	When impact is detected	ON
			Normal condition	OFF
			When short circuit is present	Short
			When open circuit is present	Open
21	Driver's door lock actuator lock switch	DR DOR LCK SW	Locked	ON
21	Driver's door lock actuator lock switch	DR DOR LCK SW	Other than "locked"	OFF
22	Driver's door lock actuator unlock switch	DR DOR UNLCK SW	Unlocked	ON
22	Driver's door lock actuator unlock switch	DR DOR UNLCK SW	Other than "Unlocked"	OFF
26	Central door lock switch	CNTR DOOR LCK	-	OFF
27	Central door unlock switch	CNTR DOR ULCK	-	OFF
36	Diagnosis connector	MUT DIAG CON.	When the diagnosis control is connected	ON
36	Diagnosis connector	MUT DIAG CON.	When the diagnosis control is not connected	OFF

ETACS ANALOGUE DATA CHART

Item No.	Check items	Display on MUT-II/III	How to check
02	Windshield wiper intermittent volume	WPR VOL VOLT	Displays the voltage in the windshield wiper intermittent volume. Changes in accordance with the position of the windshield wiper intermittent volume.
03	Vehicle speed signal	SPEED SENSOR	Displays the vehicle speed. Changes in accordance with the vehicle speed.
04	Interior lamp automatic shutdown timer period	RM LMP TIMER	Displays interior lamp automatic shutdown period (timing).
05	Headlamp automatic shutdown timer period	H/L A.CUT TMR	Displays headlamp automatic shutdown period (timing).
06	Power window key-off timer period	P/W KY OF TMR	Displays power window key-off timer period (timing).
07	Wiper intermittent period	WPR INT TIME	Displays the windshield wiper intermittent period which is calculated from the windshield wiper intermittent volume position and the vehicle speed signal. Changes according to the windshield wiper intermittent volume position and the vehicle speed.