Terminal No.
|
Check item
|
Inspection condition
|
Standard value
|
|---|
39
|
Stoplight switch
|
|
System voltage
|
|
|
1 V or less
|
64
|
Input shaft speed sensor
|
- Measure between terminals 64 and 88 with an oscilloscope.
- Selector lever position: Sport mode (3rd gear)
|
Refer to  , Inspection Procedure Using an Oscilloscope.
|
66
|
Inhibitor switch: P
|
- Selector lever position: P
|
System voltage
|
- Selector lever position: Other than above
|
1 V or less
|
67
|
Inhibitor switch: R
|
- Selector lever position: R
|
System voltage
|
- Selector lever position: Other than above
|
1 V or less
|
68
|
Shift switch (Down)
|
- Selector lever operation: Downshift and hold the selector lever
|
System voltage
|
- Selector lever operation: Other than above
|
1 V or less
|
70
|
Crank angle sensor
|
Engine: Idling
|
1.5 -
2.5 V
|
73
|
Output shaft speed sensor
|
- Measure between terminals 73 and 88 with an oscilloscope.
- Selector lever position: Sport mode (3rd gear)
|
Refer to , Inspection Procedure Using an Oscilloscope.
|
75
|
Inhibitor switch: N
|
- Selector lever position: N
|
System voltage
|
- Selector lever position: Other than above
|
1 V or less
|
76
|
Inhibitor switch: D
|
- Selector lever position: D
|
System voltage
|
- Selector lever position: Other than above
|
1 V or less
|
77
|
Shift switch (Up)
|
- Selector lever operation: Upshift and hold the selector lever
|
System voltage
|
- Selector lever operation: Other than above
|
1 V or less
|
79
|
Vehicle speed signal
|
- Measure between terminals 79 and earth with an oscilloscope.
- Selector lever position: Sport mode (3rd gear)
|
Refer to , Inspection Procedure Using an Oscilloscope.
|
85
|
Select switch
|
- Selector lever position: Sport mode
|
System voltage
|
- Selector lever position: Other than above
|
1 V or less
|
119
|
A/T fluid temperature sensor
|
A/T fluid temperature: 20°C
|
3.8 -
4.0 V
|
A/T fluid temperature: 40°C
|
3.2 -
3.4 V
|
A/T fluid temperature: 80°C
|
1.7 -
1.9 V
|
121
|
Shift indicator C
|
Measure the voltage when each shift range is displayed by using actuator function (item No.07 to 10) on the MUT-II/III.
|
1st
|
1 V or less
|
2nd
|
1 V or less
|
3rd
|
1 V or less
|
4th
|
8 -
10 V
|
123
|
Solenoid valve power supply
|
Ignition switch: LOCK (OFF)
|
1 V or less
|
Ignition switch: ON
|
System voltage
|
124
|
Solenoid valve power supply
|
Ignition switch: LOCK (OFF)
|
1 V or less
|
Ignition switch: ON
|
System voltage
|
125
|
Shift indicator B
|
Measure the voltage when each shift range is displayed by using actuator function (item No.07 to 10) on the MUT-II/III.
|
1st
|
1 V or less
|
2nd
|
8 -
10 V
|
3rd
|
8 -
10 V
|
4th
|
1 V or less
|
127
|
A/T control relay
|
Always
|
1 V or less
|
128
|
LR solenoid valve
|
- Selector lever position: P
|
System voltage
|
- Selector lever position: Sport mode (2nd gear)
|
6 -
9 V
|
130
|
DCC clutch solenoid valve
|
- Selector lever position: P
|
System voltage
|
131
|
Earth
|
Always
|
1 V or less
|
134
|
Shift indicator A
|
Measure the voltage when each shift range is displayed by using actuator function (item No.07 to 10) on the MUT-II/III.
|
1st
|
8 -
10 V
|
2nd
|
1 V or less
|
3rd
|
8 -
10 V
|
4th
|
1 V or less
|
135
|
A/T fluid temperature warning lamp <Except for Hong Kong spec.>
|
Ignition switch: LOCK (OFF) to ON
|
1 V or less to System voltage (after several seconds have elapsed)
|
136
|
2ND solenoid valve
|
- Selector lever position: Sport mode (2nd gear)
|
System voltage
|
- Selector lever position: P
|
6 -
9 V
|
137
|
UD solenoid valve
|
- Selector lever position: Sport mode (1st gear)
|
System voltage
|
- Selector lever position: P
|
6 -
9 V
|
138
|
OD solenoid valve
|
- Selector lever position: Sport mode (3rd gear)
|
System voltage
|
- Selector lever position: P
|
6 -
9 V
|
139
|
Earth
|
Always
|
1 V or less
|
)