|
| INSPECTION <EXCEPT VEHICLES FOR HONG KONG SPEC AND ARGENTINA>
|
| POWER WINDOW SWITCH CONTINUITY CHECK
Remove the power window switch (Refer to GROUP 52A, Door Trim  ).
|
| |
|
MAIN SWITCH <LH DRIVER VEHICLES>
SWITCH POSITION
|
TESTER CONNECTION
|
SPECIFIED CONDITION
|
|---|
FRONT (LH)
|
UP
|
8 -
13, 9 -
12,
|
Less than 2 ohms
|
OFF
|
8 -
12, 9 -
12
|
Less than 2 ohms
|
DOWN
|
9 -
13, 8 -
12
|
Less than 2 ohms
|
FRONT (RH)
|
UP
|
3 -
13, 11 -
12*
|
Less than 2 ohms
|
OFF
|
3 -
12*, 11 -
12*
|
Less than 2 ohms
|
DOWN
|
3 -
12*, 11 -
13
|
Less than 2 ohms
|
REAR (LH)
|
UP
|
1 -
13, 2 -
12*
|
Less than 2 ohms
|
OFF
|
1 -
12*, 2 -
12*
|
Less than 2 ohms
|
DOWN
|
1 -
12*, 2 -
13
|
Less than 2 ohms
|
REAR (RH)
|
UP
|
6 -
12*, 13 -
14
|
Less than 2 ohms
|
OFF
|
6 -
12*, 12*-
14
|
Less than 2 ohms
|
DOWN
|
6 -
13, 12*-
14
|
Less than 2 ohms
|
MAIN SWITCH <RH DRIVER VEHICLES>
SWITCH POSITION
|
TESTER CONNECTION
|
SPECIFIED CONDITION
|
|---|
FRONT (LH)
|
UP
|
3 -
13, 11 -
12
|
Less than 2 ohms
|
OFF
|
3 -
12, 11 -
12
|
Less than 2 ohms
|
DOWN
|
3 -
12, 11 -
13
|
Less than 2 ohms
|
FRONT (RH)
|
UP
|
8 -
13, 9 -
12*
|
Less than 2 ohms
|
OFF
|
8 -
12*, 9 -
12*
|
Less than 2 ohms
|
DOWN
|
9 -
13, 8 -
12*
|
Less than 2 ohms
|
REAR (LH)
|
UP
|
1 -
13, 2 -
12*
|
Less than 2 ohms
|
OFF
|
1 -
12*, 2 -
12*
|
Less than 2 ohms
|
DOWN
|
1 -
12*, 2 -
13
|
Less than 2 ohms
|
REAR (RH)
|
UP
|
6 -
12*, 13 -
14
|
Less than 2 ohms
|
OFF
|
6 -
12*, 12*-
14
|
Less than 2 ohms
|
DOWN
|
6 -
13, 12*-
14
|
Less than 2 ohms
|
NOTE: *: Set the window lock switch to UNLOCK position.
|
| |
|
SUB SWITCH
SWITCH POSITION
|
TESTER CONNECTION
|
SPECIFIED CONDITION
|
|---|
UP
|
5 -
7, 6 -
8
|
Less than 2 ohms
|
OFF
|
4 -
7, 6 -
8
|
Less than 2 ohms
|
DOWN
|
4 -
7, 5 -
6
|
Less than 2 ohms
|
|
| POWER WINDOW MOTOR CONTINUITY CHECK
|
| |
|
<FRONT DOOR>
TESTER CONNECTION
|
SLIDER POSITION
|
|---|
- Connect terminal No. 4 and the negative battery terminal.
- Connect terminal No. 1 and the positive battery terminal.
|
UP
|
- Connect terminal No. 1 and the negative battery terminal.
- Connect terminal No. 4 and the positive battery terminal.
|
DOWN
|
|
| |
|
<REAR DOOR>
TESTER CONNECTION
|
SLIDER POSITION
|
|---|
- Connect terminal No. 2 and the negative battery terminal.
- Connect terminal No. 1 and the positive battery terminal.
|
UP
|
- Connect terminal No. 1 and the negative battery terminal.
- Connect terminal No. 2 and the positive battery terminal.
|
DOWN
|
|
| POWER WINDOW MOTOR CHECK
- Connect a battery directly to the motor terminals and check that the motor runs smoothly.
- Check that the motor runs in the opposite direction when the battery is connected with the polarity reversed.
- If defect is found, replace the window regulator as an assembly.
|
)
)
)
)