[52B] SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - - TROUBLESHOOTING - DIAGNOSTIC TROUBLE CODE PROCEDURES - Diagnosis code 41: IG1 Power Supply Circuit System (Fuse No.2 Circuit)PRINT PAGE / INDEX / PRIOR / NEXT
Diagnosis code 41: IG1 Power Supply Circuit System (Fuse No.2 Circuit)
OPERATION
  • The SRS-ECU is powered from the ignition switch (IG1).
  • The SRS-ECU power is supplied from two circuits. Even if one circuit is shut off, the air bag can inflate.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set if the voltage between the IG1 terminals (fuse No.2 circuit) and earth is lower than a predetermined value for a continuous period of 5 second or more. However, if the vehicle condition returns to normal, diagnosis code number 41 will be automatically erased, and the SRS warning lamp will switch off.
PROBABLE CAUSES
  • Damaged wiring harnesses or connectors
  • Malfunction of the SRS-ECU
DIAGNOSIS PROCEDURE
STEP 1. Check junction block fuse number 2.
Q: Is the fuse burned out?
YES:  Go to Step 4.
NO:  Go to Step 2.
STEP 2. Check the power supply circuit for open circuit at the SRS-ECU connector C-115.
  1. Disconnect the negative battery terminal.
  1. Disconnect SRS-ECU connector C-115.
  1. Connect the negative battery terminal.
  1. Turn the ignition switch to the "ON" position.
   
     CAUTION
     Do not insert a test probe into the terminal from its front side directly as the connector contact pressure may be weakened.
  1. Measure the voltage between C-115 harness side connector terminal 16 and body earth.
    2. OK: 9 V or more.
Q: Is the check result normal?
YES:  Erase the diagnosis code memory, and check the diagnosis code. If diagnosis code 41 sets, replace the SRS-ECU (Refer to ). Then go to Step 10 .
NO:  Go to Step 3.
STEP 3. Check the harness for open circuit between SRS-ECU connector C-115 (terminal No.16) and the ignition switch connector C-303 (terminal No.2).
NOTE: After inspecting intermediate connectors C-205 and C-203, inspect the wiring harness. If intermediate connectors are damaged, repair or replace them. Then go to Step 10.
Q: Is harness between SRS-ECU connector C-115 (terminal No.16) and the ignition switch connector C-303 (terminal No.2) in good condition?
YES:  Go to Step 10.
NO:  Repair the harness wire between SRS-ECU connector C-115 and the ignition switch connector C-303. Then go to Step 10.
STEP 4. Check a burned-out fuse.
  1. Replace the fuse.
  1. Turn the ignition switch to the "ON" position, wait for at least one minute and then turn the ignition switch to the "LOCK" (OFF) position.
  1. Check the fuse.
Q: Is the fuse in good condition?
YES:  Go to Step 10.
NO:  Go to Step 5.
STEP 5. Check the SRS-ECU power supply circuit for short circuit to earth at the junction block connector C-205.
  1. Disconnect junction block connector C-205, and measure at the wiring harness side.
   
     CAUTION
     Do not insert a test probe into the terminal from its front side directly as the connector contact pressure may be weakened.
  1. Check for continuity between terminal 24 and body earth.
    2. OK: Open circuit
Q: Is the check result normal?
YES:  Go to Step 6.
NO:  Go to Step 8.
STEP 6. Check the fuse number 2-related circuit at junction block connector C-205.
  1. Disconnect junction block connector C-205, and measure at the wiring harness side.
   
     CAUTION
     Do not insert a test probe into the terminal from its front side directly as the connector contact pressure may be weakened.
  1. Check for continuity between terminal 25 and body earth.
    2. OK: Open circuit
Q: Is the check result normal?
YES:  Check the other circuit, which flows through fuse number 2.
NO:  Go to Step 7.
STEP 7. Check the harness for short circuit to earth between junction block connector C-205 (terminal No.25) and combination meter connector C-04 (terminal No.42).
Q: Is the harness wire between junction block connector C-205 (terminal No.25) and combination meter connector C-04 (terminal No.42) in good condition?
YES:  Go to Step 10.
NO:  Repair the harness wire between junction block connector C-205 and combination meter connector C-05. Then go to Step 10.
STEP 8. Check the power supply circuit for short circuit to earth at the SRS-ECU connector C-115.
  1. Disconnect SRS-ECU connector C-115, and measure at the wiring harness side.
   
     CAUTION
     Do not insert a test probe into the terminal from its front side directly as the connector contact pressure may be weakened.
  1. Check for continuity between terminal 16 and body earth.
    2. OK: Open circuit
Q: Is the check result normal?
YES:  Erase the diagnosis code memory, and check the diagnosis code. If diagnosis code 41 sets, replace the SRS-ECU. (Refer to ). Then go to Step 10 .
NO:  Go to Step 9.
STEP 9. Check the harness for short circuit to earth between SRS-ECU connector C-115 (terminal No.16) and junction block connector C-205 (terminal No.24).
Q: Are harness wires between SRS-ECU connector C-115 (terminal No.16) and junction block connector C-205 (terminal No.24) in good condition?
YES:  Go to Step 10.
NO:  Repair the harness wire between SRS-ECU connector C-115 and junction block connector C-205. Then go to Step 10.
STEP 10. Check whether the diagnosis code is reset.
Q: Is diagnosis code 41 set?
YES:  Return to Step 1.
NO:  The procedure is complete (If no malfunctions are found in all steps, an intermittent malfunction is suspected). Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points .
[52B] SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - - TROUBLESHOOTING - DIAGNOSTIC TROUBLE CODE PROCEDURES - Diagnosis code 41: IG1 Power Supply Circuit System (Fuse No.2 Circuit)PRINT PAGE / INDEX / PRIOR / NEXT
©2004 Mitsubishi Motors Corporation