Pre-removal and Post-installation Operation
|
<2000-SOHC>
)
| Removal steps |
|||
|---|---|---|---|
| 1. |
Oil reservoir |
||
>>G<< |
2. |
Suction hose |
|
| >>F<< |
3. |
Return hose |
|
| 4. |
Tie rod end and knuckle connection |
||
| >>B<< |
5. |
Self-locking nut |
|
| 6. |
Stabilizer rubber |
||
| 7. |
Collar |
||
| 8. |
Eye bolt |
||
| 9. |
Gasket |
||
| >>A<< |
10. |
Pressure hose assembly |
|
| 11. |
Return tube |
||
| 12. |
O-ring |
<2000-DOHC and 2400 (Except MIVEC)>
)
| Removal steps |
|||
|---|---|---|---|
| 1. |
Oil reservoir |
||
| >>H<< |
2. |
Return hose |
|
| >>G<< |
3. |
Suction hose |
|
| >>F<< |
4. |
Return hose |
|
| >>E<< |
5. |
Return hose |
|
| >>D<< |
6. |
Return hose |
|
| 7. |
Return tube assembly |
||
| • |
Front bumper assembly (Refer to GROUP 51, Front Bumper Assembly  <2000>, <2400>.) |
||
| 8. |
Cooler tube assembly |
||
| 9. |
Tie rod end and knuckle connection |
||
| >>C<< |
10. |
Self-locking nut |
|
| 11. |
Stabilizer rubber |
||
| 12. |
Stabilizer link |
||
| 13. |
Eye bolt |
||
| 14. |
Gasket |
||
| >>A<< |
15. |
Pressure hose assembly |
|
| 16. |
Return tube |
||
| 17. |
O-ring |
<2400 (MIVEC)>
)
| Removal steps |
|||
|---|---|---|---|
| 1. |
Oil reservoir |
||
| >>H<< |
2. |
Return hose |
|
| >>G<< |
3. |
Suction hose |
|
| >>F<< |
4. |
Return hose |
|
| >>E<< |
5. |
Return hose |
|
| >>D<< |
6. |
Return hose |
|
| 7. |
Return tube assembly |
||
| • |
Front bumper assembly (Refer to GROUP 51, Front Bumper Assembly <2400>.) |
||
| 8. |
Cooler tube assembly |
||
| • |
Tie rod end and knuckle connection (Refer to .) |
||
| • |
Stabilizer link (Refer to GROUP 33, Stabilizer Bar <2000-DOHC
and 2400 >.) |
||
| 9. |
Eye bolt |
||
| 10. |
Gasket |
||
| >>A<< |
11. |
Pressure hose assembly |
|
| 12. |
Return tube |
||
| 13. |
O-ring |
)
Install the pressure hose assembly so that its plate is positioned as shown in the illustration.
)
Tighten the self-locking nut until the stabilizer link thread part protruding length meets
the standard value.
Standard value (A): 22 ±
1.5 mm
)
Tighten the self-locking nut until the stabilizer link thread part protruding length meets
the standard value.
Standard value (A): 9.4 ±
0.4 mm
)
)
Install the return hose so that the marking is positioned as shown in the illustration.
)
Install the return hose so that the marking is positioned as shown in the illustration.
)
Install the return hose so that the clip is positioned as shown in the illustration.
)
)
Install the suction hose so that the marking is positioned as shown in the illustration.
)
Install the return hose so that the markings are positioned as shown in the illustration.